Lieferzeit in ganz Litauen: 5-10 Werktage
Lieferpreis an die angegebene Adresse: 3 Euro
Trumpai apie prekę
Prekė: Žibintų klijavimo ir regeneravimo rinkinys. Kategorija: Įrankių rinkiniai.
- Gamintojas: Auto Gamma
- Modelis: Zestaw do Rozklejenia Sklejania Lamp Twardy
Products that include our set:
- Pliers for unraveling headlights – 1 piece
- Butyl glue for re-gluing 7mm/6m – 1 piece
- Liquid for unfolding lamps 20 ml – 1 piece
- Syringe with needle – 1 piece
The only such solution on the market!
If you have never repaired a headlight that has been damaged yourself before, we come to you with the right kit. All headlights are glued together at the point of contact of the housing with the lampshade. Using our modern kit, you can save money, as well as make such a repair completely yourself.
How does our kit work?
Liquid for unraveling headlights and syringe allows you to unravel lamps glued on hard glue. The special composition of the liquid causes softening of the glue.
Professional pliers designed specifically for us to disassemble lamps allow easy and convenient opening of the housing from the lampshade.
The included butyl glue, was manufactured using for car headlights, it should be properly disassembled at the place of connecting the lampshade with the housing and you can enjoy the tightness of lamps often better than on the original glue.
High-quality liquid for unraveling lamps
The liquid is used to break down the headlights glued on a hard glue. The solvent after properly heating the lamp and introducing it into the reflector gap makes it easier to disassemble it. Especially recommended for lamps mounted on hard glue. Thanks to our professional liquid for spreading lamps on hard glue, everyone will be able to carry out this activity independently at home, saving their time and resources.
Professional Headlight Unfolding Pliers
Professional pliers for unfolding lamps or headlights are designed specifically for separating lampshades from the housing. Thanks to the use of specially profiled pliers, they are able to separate any type of reflector from each other. They will work in any case and can easily cope with often troublesome and impossible to disassemble.
Butyl glue for car headlights
Butyl adhesive is an effective agent that guarantees, among other things, very good adhesion to the lamp shade and housing and maintaining flexibility for a long time. Available in black. The big advantage of the mass is that it is flexible and can be formed in any way, depending on your needs. That is, both shorten and stretch, and all this in order to achieve the required diameter and shape. The product is resistant to water and all kinds of adverse weather conditions in the form of high or low air temperature. The adhesive is resistant to UV radiation.
A simple solution that everyone can handle
Separating the lampshade from the housing is not as easy as you think, so we have specially completed all the necessary tools to perform such a service yourself.
High efficiency
The glue included in the kit is enough to re-seal up to four lamps. Available, it comes in one round strip, which you can freely shorten to adjust the length to the lamp accordingly.
See the instructions for use in the video:
https://www.youtube.com/watch?v=VUKRorgFmBg
How to use for lamps connected on hard glue:
- The headlamp should be heated for 7-10 minutes in the oven at about 130°C
- Once removed from the oven, please pry the housing (e.g. with a sharp screwdriver) from the lampshade so that a gap is formed that allows the introduction of liquid.
- After introducing the liquid with pliers, we open the lampshade from the housing
- If the lamp cools down and has not been completely disassembled, repeat the procedure
- To re-glue the lamps, remove the completely factory glue then add the right amount of new, heat the entire reflector again for 5-7 minutes in the oven at about 100 ° C and after pulling out connect the lampshade with the housing until the glue solidifies
- For people who have a problem with self-execution of the service, we provide a video showing the exchange step by step
Specifications
| Group | Name | Value |
|---|---|---|
| Parametry | Condition | new |
| Parametry | Invoice | With VAT invoice |
| Parametry | Brand | Auto Gamma |
| Parametry | Manufacturer code | Zestaw do Rozklejenia Sklejania Lamp Twardy |
| Parametry | Product weight with unit packaging | 0.2 kg |
| Parametry | EAN (GTIN) | 5905255201620 |
| Parametry | Number of items in the set | 4 |