Mobilus žirklinis keltuvas 3,5T PX-3500H 1,4M 230V

Trumpai apie prekę

Prekė: Mobilus žirklinis keltuvas 3,5T PX-3500H 1,4M 230V. Kategorija: Žirkliniai keltuvai.

• Gamintojas: Normet
• Modelis: PX-3500H

The Normet 3,5T mobile scissor lift is a modern solution for workshops that expect high comfort, safety and mobility. Thanks to the maximum lifting height of up to 1,4m, it provides much greater convenience than most mobile lifts available on the market.

It is the lifting height that distinguishes this model both in the NORMET offer and from the competition. It allows you to perform most of the service work in a comfortable position without having to bend down.

Lifting height up to 1,4m!!!!

The lift allows you to lift the vehicle to a height of 1,4m, thanks to which the mechanic has convenient access to the suspension, braking system, exhaust and chassis.

It is one of the largest lifting heights among mobile scissor lifts available on the market.

ADVANTAGES :

- comfortable standing work,

- easier access to the entire chassis,

- greater ergonomics of work,

- less operator fatigue.

Lifting capacity 3500 kg

The robust design enables safe lifting of passenger cars, SUVs, vans and most commercial vehicles weighing up to 3,5 tons.

Long ramps – up to 60cm

The lift is equipped with extremely long ramps with a length of 60 cm.

Thanks to this, lower cars enter it without any problems:

Long ramps significantly reduce the angle of inrun and eliminate the risk of hooking the bumper or thresholds.

Advantages :

- better vehicle positioning on platforms

- the possibility of entering the lift with lower vehicles

- Reduced risk of damage to bumpers

Platforms with a length of 173 cm

The lift platforms have a length of 173 cm, thanks to which they provide a comfortable support space for a wide range of vehicles.

Lift support (additional short shears)

One of the biggest advantages of this model is the use of an additional lift support system.

Getting on the lift is not everything.

In the lowest position of the lift, the actuator is located almost horizontally and its force is mostly not directed vertically upwards and is directed horizontally, which causes a significant loss of power at the very start. Therefore, our lift has an additional short shear that acts as a lever and allows you to get full power from the very beginning of lifting so low cars are not a challenge

Advantages

• full power from the very beginning of lifting,
• easier lifting of low vehicles,
• greater durability of the hydraulic system,
• smoother work.

Security is paramount!

Our lift is equipped with a number of different solutions to increase your safety when working with our lift. One of such elements is the leg guard which effectively protects against slipping the foot under the lift.

In addition, during the lowering process, the lift gives a light and sound signal to take special care.

Mechanical safety locks

When locking the lift on ratchets, the weight is based on solid mechanical teeth.

This means that even if the hydraulic system is unsealed, the vehicle remains securely supported.

This solution meets the requirements of modern workshops and significantly increases operator safety.

Advantages

• safe and stable lift position
• lack of pressure on the hydraulic system
• longer lifespan of seals
• no risk of leaving even in the event of a hydraulic system failure

Electric release of safety latches

The lift is equipped with a modern system of electric release of safety latches.

Mechanical locks are controlled by electric actuators powered by 230 V voltage, thanks to which:

• no compressor is required,
• no pneumatic hoses are needed,
• installation is much simpler,
• The device can work practically anywhere where a regular 230 V socket is available.

Convenience of work is also important control box 230 V

Convenience of work is also important

For convenient operation of the lift is a control box equipped with high-end illuminated metal buttons up, down and lock. Safety switch, power lamp and light and sound signal.

Mobile set

The lift can be easily moved around the workshop.

The set includes:

• set of transport wheels,
• ergonomic handle for movement.

Thanks to this, one lift can handle several workstations.

Easy installation - all included

The lift is delivered practically ready for operation.

Installation is very simple and does not require specialized tools.

Each user can start the device himself.

Specifications