Automobilinis pneumatinis keltuvas SNOWMAN, 13–43 cm, 3,5 t

Trumpai apie prekę

Prekė: Automobilinis pneumatinis keltuvas SNOWMAN, 13–43 cm, 3,5 t. Kategorija: Pneumatiniai keltuvai.

• Gamintojas: Stix
• Modelis: 23-03-77755

The short pneumatic snowman lift APK-3500 is designed to lift vehicles weighing up to 3,5 tons. The compact design without wheels and short handles make this model well suited for work in the duct, in limited space and in transport.

Catalog number: 23-03-77755

Model: APK-3500

Manufacturer: Stix Tool

Quantity: 1 pcs.

⚙ Technical specification:

• Maximum height: 430 mm
• Minimum height: 130 mm
• Lifting capacity: 3500 kg
• Pillow diameter: 270 mm
• Rubber foot diameter: 100 mm
• Rubber cap diameter: 180 mm
• Air connection: 1/4"
• Valves: inlet / outlet
• Safety valve: yes, EU Safety Valve
• Power supply: compressed air
• Operating pressure: 5 – 10 bar
• Lift weight: 16,3 kg
• Additional protective cover: yes, included

➡ Minimum and maximum height – practical application

The initial height is 130 mm, which allows it to slide under most passenger vehicles.

When inflated, the lift reaches 430 mm, allowing access to the wheel and suspension components.

The scope of work corresponds to typical workshop applications, such as wheel dismantling or tyre handling.

➡ 5-section telescope and rounded sleeves

Inside the lift, a telescope consisting of 5 elements with diameters: 49, 59, 69, 79 and 93 mm was used.

Each sleeve has appropriately profiled, rounded edges.

This solution reduces the risk of jamming when lifting and lowering.

The telescope is more fluid compared to structures with fewer sections. In addition, the telescope stabilizes the lift when working under load.

➡ Reinforced bellows and structural stability

The lift uses 3-level bellows with a diameter of 270 mm made of a durable rubber compound.

steel rims are used on the joints, which improve the rigidity of the entire structure.

The base made of sheet metal with a thickness of 4,5 mm increases stability during operation.

The whole has been protected with powder coating, which limits the influence of external factors.

➡ Valve section and control

The lift is controlled by two ball valves – inlet and outlet.

🟢 The green valve is responsible for lifting,

🔴 Red valve for lowering.

Their location at the handle allows convenient control of the device.

The lift is equipped with a EU Safety Valve, which controls the maximum pressure in the system. The valve was made in accordance with EN ISO 4126-1:2013 + A1:2016 + A2:2019.

If the permissible values are exceeded, it automatically drains excess air, reducing the risk of overload.

➡ Operating pressure and pneumatic power supply

The lift operates in the range of 5 – 10 bar, which corresponds to standard pneumatic installations in workshops.

Equipped with a 1/4" European type connection, it allows quick connection to compressed air without additional adapters.

➡ Rubber protective cap

The lift is equipped with a standard rubber foot and an additional overlay with a diameter of 180 mm, which covers the surface of the upper plate.

The overlay increases the surface area of contact with the vehicle, which reduces point pressure and reduces the risk of damage to chassis components. This is especially important when setting the lift under the support point and in the event of a possible shift of the vehicle.

The use of an additional layer of rubber improves contact stability and facilitates precise positioning of the lift during operation.

➡ Compact design – channel application

The lift in the short version does not have wheels and is equipped with two handles with a length of 230 mm. It works well in the canal and in a limited space, where standard models with a long handle are less comfortable.

The compact design also makes it easy to transport and store. The lift takes up less space and can be transported in the car without any problem.

➡ What distinguishes the pneumatic lift APK-3500 3,5T?

✅ Compact design without wheels (for channel operation)

✅ 5-section telescope with different sleeve diameters

✅ Rounded edges to reduce jamming

✅ No sharp structural elements

✅ Safety valve compliant with EU standard

✅ Stable structure based on 4,5mm steel base

✅ Simple valve control system

➡ Why is it worth it?

The shorter design makes the lift easier to use in limited space. Maintains the operating parameters typical of full-size lifts.

The applied construction solutions affect the stability and repeatability of work in workshop conditions.

💡 FAQ – Frequently Asked Questions

1. Is the lift suitable for low cars?

• Yes, the minimum height of 130 mm allows you to slide under vehicles with lowered suspension.

2. What do the dimensions of the telescope sleeve mean?

• These are the diameters of subsequent telescope elements (49 to 93 mm), which are responsible for stability and handling during operation.

3. Can the design cause jams?

• The rounded edges of the sleeve are used, which reduce the risk of jamming of the mechanism.

4. How does the safety valve work?

• EU Safety Valve controls the pressure and, if necessary, drains excess pressure from the system.

5. What pressure is required for operation?

• The lift operates in the range from 5 to 10 bar.

6. Does it require a special pneumatic system?

• No, the standard 1/4" quick coupler fits typical workshop installations.

7. Is this model different from the wheel version?

• Yes, it is shorter and has no wheels – it works better in the channel and tight spaces.

➡ AP/APK family of pneumatic jacks

The AP and APK series of pneumatic lifts are based on structures of various constructions and purposes, adapted to different workshop conditions.

Depending on the version, solutions such as a longer handle with wheels for easy movement or a compact design designed to work in limited space are used, e.g. in the canal.

Telescopic design and pneumatic bellows system are responsible for stability and repeatability of work when lifting the vehicle.

📷 Gallery

Specifications

Group	Name	Value
Parametry	Condition	new
Parametry	Invoice	With VAT invoice
Parametry	Product weight with unit packaging	17.5 kg
Parametry	Brand	Stix
Parametry	Manufacturer code	23-03-77755
Parametry	EAN (GTIN)	5903636080802
Parametry	Lifting capacity	3500 kg
Parametry	Minimum lifting height	130 mm
Parametry	Maximum lifting height	430 mm