Aukštadažnis O9 indukcinis šildytuvas

Trumpai apie prekę

Prekė: Aukštadažnis O9 indukcinis šildytuvas. Kategorija: Oro šildytuvai.

• Gamintojas: no brand
• Modelis: AG251003072447

Function:

1. Fine design: Inductive heating board adopts super large PCB chip design and super large heat sink, which has good heat dissipation and high power. Cooling fan interface included and can also be used for discharge, generator, high voltage inverter power supply, etc.

2. Powerful Function: The output end uses three M4 brass columns in parallel, which can be connected to other outputs, such as high voltage packets; Using 6 IRFP260 parallel resonance capacitors and 12 parallel resonances, the hob has high power and efficiency.

3. Operating Details: This induction heating circuit uses low voltage direct current power supply with low 12 to 48V, with a maximum current of 50A and a maximum power of 2500W.

4. Commonly applicable: induction heater can operate continuously under good heat dissipation conditions. Due to its moderate power, the module can be used by DIY players to perform heat treatment, such as extinguishing and annealing small parts. It can also be paired with graphite crucible (without) to melt metals such as gold, silver, copper, aluminum, etc., and heats up quickly and quickly, making it very convenient.

5. Easy to install: The compact size makes the module easy to install on your equipment and machine, perfect replacement for old and damaged parts.

Specification:

• Item Type: Induction Heater
• Material: PCB, Brass
• Input voltage: 12V-48V, recommended above 36V
• Power Requirements:
• Less than 12 V, greater than or equal to 10a
• Above 15 V, greater than or equal to 20A
• Fan: with a silent fan
• Maximum power: 2500 W.
• Maximum current: 50a

1. The heating power is very high, except for very hot boards and components, the heating capacity of brass pipes is very high. Buyers can prepare a separate water cooling system by purchasing a small water pump and a 2-meter rubber hose with an inner diameter of 4 mm.

2. When using power supplies switching power supplies, pay attention, because power supplies with high power supplies generally have a soft start function, and the output voltage increases slowly. If the Y voltage rises to 10V earlier, the circuit cannot withstand vibration due to insufficient voltage, while causing the behavior of two MOS transistors and the burnout of components. Therefore, it is necessary to change the supply voltage to stabilize, and then connect it to the heating circuit by induction.

3. When heating metal objects, do not heat too much metal, otherwise it can cause power overload. Add a 35A fuse or ammeter and the air switch will be better. (Packaging not included)

• 4.

5. The package is equipped with a heating ring with a diameter of 60 mm and a design voltage of 36 V. If a power supply with a voltage of 40 or higher is used, it is used for heating with an internal diameter of 70 mm above the diameter of the heating ring, the water pump adopts 12 V DC power supply. Use a separate power regulator module to burn the fan and water pump.

6. The minimum input voltage of the module is 12 V, which does not mean that you can use the entire 12 V power supply. Some novice buyers can use smaller power supplies. This module has specific voltage and current requirements, and the 12V voltage current must be greater than 10A. If the battery level is too low, you can use a power adapter. This greatly reduces the power output. When the voltage is lower than 12 V, this will preserve both the moss and the burnout of the MOS transistor.

7. If you encounter MOS pipe heating, the first thing to consider is whether the output power meets the requirements.

8. Do not empty the board, otherwise it emits a high noise frequency and burn out the MOS transistor.

9. It is recommended to use a 36 V 20A power supply for induction heating. The 12V power supply is too small and almost unresponsive, and the 12V power supply can easily cause the power output voltage to drop. The use of a voltage lower than 12 V is very dangerous.

10. The power of induction heating is excellent, so heating is a normal phenomenon and it is necessary to do a good job in heat dissipation. Induction heating, recommended power supply is 48V or higher. If the power supply is above 24V, the power supply is above 20A. The higher the voltage, the greater the current, the greater the heating power and faster the heating.

List of packages:

• 1 x Induction Heater
• 1 x Brass Ring

Specifications