Vandens aeratorius, 1" žalvario kasetė, 100 l/min

Trumpai apie prekę

Prekė: Vandens aeratorius, 1" žalvario kasetė, 100 l/min. Kategorija: Filtrai ir vandens minkštikliai.

• Gamintojas: no brand
• Modelis: 1
• Talpa: 0 l

⭐ ASPIRATOR FOR AERATION OF WATER AWODA 1"

✅ Aspirator brass AWODA 1" is a simple and effective element of the water treatment system, designed for aeration and oxygenation of water without the use of electricity and chemicals.

✅ The device operates on the principle of the Venturi effect. During the flow of water, a vacuum is created that allows air to be sucked into the installation. This process supports the oxidation of iron and manganese before the further stage of filtration.

✅ Aspirator will work primarily in installations using wellwater, de-ironing filters and deposits designed to remove iron and manganese.

⭐ The most important advantages of an aspirator

✅ Aeration without electricity – the device uses water flow and does not require electrical power.

✅ Without the use of chemistry – the air is sucked mechanically thanks to the Venturi effect.

✅ Supports de-ironing – oxygenation of water promotes the oxidation of dissolved iron before the filtration stage.

✅ Supports demanganization – proper aeration can support the operation of systems designed to reduce manganese.

✅ Connection 1" – a variant designed for installations with a capacity of up to about 100 l/min.

✅ Brass construction – durable body adapted for installation in water installation.

✅ Simple construction – a small number of elements limits the scope of required service.

✅ Assembly without bypass – the aspirator should be mounted directly in the water flow line.

⭐ How does an aspirator work?

✔ During the flow of water through the narrowing inside the aspirator, a pressure difference occurs according to the Venturi effect.

✔ The resulting vacuum allows air to be sucked into the stream of flowing water.

✔ The supplied oxygen supports the oxidation process of iron and manganese compounds.

✔ Oxidized compounds can then be stopped by a properly selected filter bed in an iron remover or demanganizer.

✔ The effectiveness of the aspirator depends on the correct flow, pressure and method of installation.

⭐ Installation performance requirements

✔ The selection of the correct aspirator diameter should be adapted to the actual flow in the installation.

✔ Too small diameter can cause excessive pressure losses and limit system performance.

✔ Variant 1" is designed for installations with a capacity of up to 100 l/min.

✔ With a flow rate exceeding 100 l/min, it is recommended to use the 1 1/4" variant.

✔ The correct selection of the aspirator has a direct impact on the stability of aeration and the operation of the entire installation.

⭐ Requirements for pump

✔ For proper operation of the aspirator, the pump should ensure adequate pressure and flow efficiency.

✔ The minimum pump lifting height required is 60 m.

✔ The recommended operating point of the system is 60 l/min at 3 bar.

✔ Adequate hydraulic parameters are necessary to obtain a pressure difference enabling effective air intake.

✔ A pump with too low efficiency or lifting height can limit the aeration efficiency.

⭐ Correct installation of the aspirator

✔ On the outlet side of the aspirator, leave a minimum of 25 cm of straight section of pipe.

✔ It is also recommended to keep the installation section as simple as possible in front of the aspirator.

✔ Directly at the device, the installation of knees, tees and other elements causing strong flow turbulence should be avoided.

✔ A simple section of the pipeline helps stabilize the flow and increases the efficiency of the device.

✔ Aspirator does not require bypass and do not use bypass, as it may disturb the required hydraulic conditions.

⭐ Absolute assembly order

✅ The correct order of installation elements should look like this:

PUMP → CHECK VALVE → ASPIRATOR → PRESSURE SWITCH

✔ Maintaining this order allows you to create the conditions necessary for the proper operation of the aspirator.

✔ Incorrect placement of components can cause problems with air intake and unstable operation of the entire system.

⭐ Technical specification

✔ Product: aspirator for aeration of water

✔ Brand: AWODA

✔ Body material: brass

✔ Connection: 1"

✔ Working principle: Venturi effect

✔ Recommended installation capacity: up to 100 l/min

✔ Recommended operating point: 60 l/min at 3 bar

✔ Minimum pump lifting height: 60 m

✔ Minimum straight section behind the aspirator: 25 cm

✔ Electrical power supply: not required

✔ Use of chemicals: not required

✔ Bypass: do not use

✔ Application: aeration of water before the de-ironing and de-manganizing process

Specifications

Group	Name	Value
Parametry	Condition	new
Parametry	Invoice	With VAT invoice
Parametry	Brand	no brand
Parametry	Kind	other
Parametry	Capacity	0 l
Parametry	Manufacturer code	ASP1
Parametry	EAN (GTIN)	5905344951429
Parametry	Packaging status	original
Parametry	Model	1