Suvirinimo aparatas TWINMIG2 200A TIG/MMA komplektas

Trumpai apie prekę

Prekė: Suvirinimo aparatas TWINMIG2 200A TIG/MMA komplektas. Kategorija: Pusiau automatiniai suvirinimo aparatai.

• Gamintojas: Welder Fantasy
• Modelis: SET1-TWINMIG2200

WELDER FANTASY TWINMIG2 3w1 - WELDING KIT #1

Brand: Welder Fantasy | Welding methods: MIG, MMA,TIG LIFT | Power supply: AC 230V/50Hz | Welding current: 200A | Efficiency: 60%

STANDARD EQUIPMENT

• Welder Fantasy TWINMIG II 200,
• Holder MB15-3m,
• Mass holder 4m,
• Electrode holder 4m,
• Steel rollers 0.8-1.0mm V (in wire feeder),
• Additional rollers for steel 0.6 - 0.8mm V, 0.8 - 1.0mm V,
• Additional roll for aluminium 0.8 - 1.0mm U,
• Additional roll for FLUX 0.8 - 1.0mm R,
• brush-hammer,
• Welding mask,
• Gas hose,
• Operating instructions and warranty card.

OPTIONAL EQUIPMENT

• Vogelmann Gas bottle MIX Ar/CO2 8l 150bar
• Vogelmann Gas reducer Exakt
• Vogelmann Spray anti-chipping 400ml
• Vogelmann Welding wire SG2 0,8mm 5kg

All-in-one Welder Fantasy TWINMIG2 is designed for manual arc welding in the following methods:

• GMAW (Gas Metal Arc Welding) - MIG/MAG
• Welding with self-shielded wire FCAW (without gas shield)
• MMA (Manual Metal Arc Welding)
• TIG LIFT (the arc glow occurs when the electrode comes into contact with the welded element).

Semi-automatic welding machine is the most modern welding device on the market, designed for welding materials such as: carbon steels, alloy steels (stainless, acid-resistant), as well as aluminum alloys. Properly selected welding inductance contributes to reducing the amount of chipping.

Intuitive, easy control panel allows you to quickly set all the most important welding parameters. Thanks to synergic settings it is possible to automatically select welding parameters.

The device has smooth regulation of voltage and intensity of welding current and is equipped with an overload system thermal protection protecting against excessive heating of integrated circuits.

In order to increase the comfort of work and reduce the noise level, the fan turns on automatically instead of working continuously when the device is turned on.

Thanks to the polarity change cable, it is possible to weld without shielding gas. Thanks to the IGBT transistors used, the device has an efficiency of 60% and is characterized by low weight and reliability.

TECHNICAL DATA:

• Power supply voltage [V]:1~230
• Current frequency [Hz]: 50/60
• Power consumption [kVA]: 7
• Prompt security min. [A]:20
• Isolation class: F
• Housing protection rating: IP21S
• Dimensions [mm]: 500x215x340
• Weight [kg]: 9,3
• Rated output voltage [V]: 15.3-27
• Welding current range [A]: 25-200
• Work cycle for temp. environment: 40°C % [A] 60% / 200 100% / 130
• Welding wire diameter: 0.6 / 0.8 / 0.9 / 1.0
• Output voltage adjustment: smooth
• Inductance adjustment: liquid
• Welding current range [A]: 20-200
• Welding current range [A]: 26-20

IGBT TECHNOLOGY

Modern technology based on bipolar transistors with an isolated gate. It combines the ease of control of field transistors with high breakdown voltage and switching speed of bipolar transistors. The use of IGBT technology has the effect of significantly extending the reliable operation of welding equipment.

PROTECTION AGAINST OVERHEATING

The IGBT module is protected from overheating by a protective installation that turns off the welding circuit of the device. After a few minutes, the welding machine cools down to a temperature that allows it to be turned on again.

Do not disconnect the power supply during this time, because the continuously operating fan cools the internal heat sinks of the device in order to lower the temperature faster.

After restarting, remember to limit the welding parameters in order to continue the continuous operation of the device.

WORK CYCLE

The work cycle is based on a 10-minute period. The 60% duty cycle means that after 6 minutes of operation of the device, a 4-minute break is required. The 100% duty cycle means that the device can work continuously, without interruptions.

DEGREE OF PROTECTION

IP determines the extent to which the device is resistant to solid and water contaminants entering. IP21S means that the device is adapted to work in enclosed spaces

MIG/MAG

Arc welding in gas shields is one of the most commonly used processes for the manufacture of welded structures. The semi-automatic welding process involves melting the edges of the welded object and the material of the hot melt electrode with the heat of an electric arc glowing between the electrode in the form of a solid wire and the welded detail, in an inert or active gas shield.

FCAW - WELDING WITHOUT GAS

Thanks to the polarity change function, it is possible to weld without shielding gas, with self-shielding wire FCAW. It is a method using self-shielding core wire for welding (in all positions) steel of normal and increased strength, not exceeding 510 MPa.

MMA DC+

Arching is created by touching the end of the electrode to the welded material. MMA DC+ means welding with positive polarity - more heat is emitted in the material and less in the electrode.

MMA DC

The difference between MMA DC+ is that the polarity in MMA DC - mode is negative, so the heat distribution is reversed - more heat is emitted on the electrode and less in the welded material.

ARC FORCE

Increasing or decreasing the length of the welding arc depending on the distance of the electrode from the material being welded. Allows you to adjust the dynamics of the welding arc. Shortening the arc length is accompanied by an increase in welding current, which results in stabilisation of the arc.

HOT START

The function is designed to prevent sticking the electrode to the material and is a great convenience when arcing. It works at the moment of arcing, causing a temporary increase in the welding current above the value set by the welder.

VRD

The VRD function reduces the voltage in the unloaded state. The correct voltage value is restored only just before the arc is ignited. This minimizes the risk of electric shock, but in some cases it can make it difficult to light the arc.

REGULATION OF INDUCTANCE

Inductance adjustment allows you to optimize the arc characteristics depending on the thickness of the welded element and the welding method and conditions. The function is useful during MIG/MAG welding of thin elements, preventing them from burning out and during soldering of galvanized elements.

The change in the value of inductance also reduces the number of welding chips during CO2 welding. The higher the inductance value (+) the number of chippings decreases when the value is negative (-), the number of chippings increases. The optimal setting of the inductance value depends on several factors and may differ from the standard recommendations, so it should be selected experimentally during welding tests.

SYNERGY

MIG/MAG welding using synergistic settings. The device selects welding parameters depending on the selected type and thickness of the material.

These parameters can be changed by the user to adjust the settings to suit their needs. Many programs have been prepared for synergistic welding.

2 ROLLER WIRE FEEDER

Professional feeder made of die-cast aluminum, has a strong motor, which allows for stable wire feeding without jamming. It is equipped with 2 drive rollers.

2T/4T

2T - Pressing the welding torch button will cause the gas to pre-flow, then ignite the arc and start welding. When the button is released, the arc will be extinguished and the gas will flow out.

4T - Pressing and releasing the welding torch button will cause the gas to pre-flow, then the arc to glow and start welding. After pressing and releasing the button again, the arc will be extinguished and the gas will flow out.

EURO CONNECTOR

Standard welding torch connection that allows you to connect various types of torches (e.g. prepared for welding Aluminum by replacing the Teflon cartridge and current tip).

EASY-TO-USE, EASY-TO-READ CONTROL PANEL:

Easy-to-use control panel enables precise and smooth adjustment of parameters. The digital display indicates the actual current during welding.

STRONG AND ROBUST CONSTRUCTION

The housing of the device is made of light and durable composites, resistant to all kinds of mechanical damage.

EASY TRANSPORT

Equipping the welding machine with a transport handle for convenience when changing jobs.

TIG DC LIFT

Welding with tungsten electrode in an inert gas shield using a handle with a gas valve in the handle. The arc is ignited by rubbing, similarly to the MMA method.

INSULATION CLASS F

Type of insulation materials used, informing about the maximum operating temperature of the transformer. Its exceeding at continuous operation reduces the service life and time of trouble-free operation of the transformer. For class F 155°C.

COOLING

The device has a cooling system with a fan which significantly increases its efficiency.

VOGELMANN GAS CYLINDER MIX AR/CO2 8L 150BAR

The cylinder filled with a mixture of Argon gases (82%) and Carbon Dioxide (18%) is intended for welding in protective gas shielding and for other industrial applications.

• Valve: W 21.8 x 1/14 DIN 477
• Content: Argon 82%, Carbon Dioxide 18%
• Capacity: 8l
• Working pressure: 150 bar
• Amount of gas: ~1,8m3

VOGELMANN EXAKT - CYLINDER REDUCER ARGON/CO2

The universal gas reducer brand VOGELMANN allows to reduce the pressure of gases taken from the cylinder to the required working pressure.

It allows you to automatically receive pressure at a possible constant level regardless of changes in inlet pressure.

• Brand: Vogelmann
• Gas type: CO2, Ar, MIX
• Thread at the inlet: W21,8x1/14
• Thread of nut at outlet: G 1/8
• Outlet connector: ø5mm
• Inlet pressure: 200bar
• Exhaust pressure: 0,5 - 10 bar
• Capacity: 20l/min

VOGELMANN WELDING WIRE SG2 5KG 0,8MM

SG2 copper welding wire designed for welding low carbon and low alloy steels in carbon dioxide shield (CO²) or a mixture of argon and dioxide gases (Ar + CO²).

• Wire diameter: 0,8 mm
• Roller weight: 5 kg
• Quality standard: SG2 / ER70S-6
• Roller type: D200
• Total spool diameter: 200 mm
• Tensile strength: 540 MPa

VOGELMANN ANTI-CHIPPING SPRAY 400ml

DESTINY

Use to protect the nozzle of the burner, tools and the surface of the welded material from melting metal chips during welding with electrical techniques.

USE

Before welding, lightly spray from a distance of 30 cm protected surface. After welding, remove the chips with a cloth.

• Features: flammable, contains PB
• Content [ml]: 400

Specifications